UJI KUAT LENTUR KAYU DENGAN TAMBALAN PADA TAKIKAN BALOK KAYU
Abstract
Penelitian ini bertujuan untuk mengetahui besarnya kuat lentur kayu yang ditambal dengan campuran serbuk kayu, resin dan hardener sebagai perekat pada balok kayu yang ditakik. Dari penelitian ini didapatkan rerata besarnya kuat lentur balok kayu johar utuh sebesar 80,94 MPa, rerata kuat lentur balok kayu dengan kedalaman takikan 1/6d dan 1/3d yang letak takikan di 1/3 bentang serat tekan berturut-turut 56,80 MPa dan 39,76 MPa, untuk takikan di 1/3 bentang serat tarik berturut-turut 52,54 MPa, 35,50 MPa, untuk takikan di 1/2 bentang serat tekan berturut-turut 48,28 MPa dan 32,66 MPa, untuk takikan di 1/2 bentang serat tarik berturut-turut 44,02 MPa dan 28,40 MPa. Untuk tambalan di 1/3 bentang serat tekan berturut-turut 65,32 MPa dan 48,28 MPa serta persentase penurunan kuat lentur terhadap balok kayu utuh sebesar 19,30% dan 40,35%, untuk tambalan di 1/3 bentang serat tarik berturut-turut 61,06 MPa dan 44,02 MPa serta penurunannya 24,56% dan 45,61%, untuk tambalan di 1/2 bentang serat tekan berturut-turut 56,80 MPa dan 39,76 MPa serta penurunannya 29,82% dan 50,88%, untuk tambalan di 1/2 bentang serat tarik berturut-turut 52,54 MPa dan 35,50 MPa serta penurunannya 35,09% dan 56,14%.
This study aims to determine the flexural strength of wood patched with a mixture of sawdust, resin and hardener as an adhesive on notched wooden beams. From this study, it was found that the average flexural strength of intact Johar wood beams was 80.94 MPa, the average flexural strength of wooden beams with notch depths of 1/6d and 1/3d where notches were located in 1/3 of the compression fiber span respectively 56.80 MPa and 39.76 MPa, for notches in 1/3 span of tension fiber respectively 52.54 MPa, 35.50 MPa, for notches in 1/2 span of compressed fiber respectively 48.28 MPa and 32.66 MPa, for notches in 1/2 span fiber tension is 44.02 MPa and 28.40 MPa, respectively. For patches in 1/3 span of compressive fiber respectively 65.32 MPa and 48.28 MPa and the percentage decrease in flexural strength of intact wood beams is 19.30% and 40.35%, for patches in 1/3 span of tensile fiber respectively 61.06 MPa and 44.02 MPa and a decrease of 24.56% and 45.61%, for patches in 1/2 span of compressed fiber respectively 56.80 MPa and 39.76 MPa and a decrease of 29.82 % and 50.88%, for patches in 1/2 span of tensile fiber respectively 52.54 MPa and 35.50 MPa and the decrease is 35.09% and 56.14%.
References
ASTM 4442-92. (2003). Standard Test Methods for derection Moisture Content Measurement of Wood-Base materials. United States.
Badan Standarisasi Nasional. (1995). SNI 03-3959-1995 Metode Pengujian Kuat Lentur Kayu di Laboratorium. Jakarta: BSN.
Badan Standarisasi Nasional. (2013). SNI 7973:2013 Spesifikasi Desain Untuk Konstruksi Kayu. Jakarta: BSN.
K. Heyne. (1987). Tumbuhan Bermanfaat Indonesia. Jakarta: Yayasan Sarana Wana Jaya.
Pujianto. (2013). Uji Kuat Lentur Kayu Dengan Tambalan Serbuk Gergaji, Serbuk Ketam dan Serbuk Amplasan Kayu. Yogyakarta: Universitas Sebelas Maret.
Copyright (c) 2024 Elia Hunggurami, Yakobus Jatang, I Made Udiana

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.